Config Show
System Configuration Setting
=========================================================================
Firmware: Version : TMH121-A V1013-MB2.4-E
Release Date : Jan 24 2006
Printout Time : SUN NOV 25 16:30:40 2007
Time Zone : GM+08:00
Primary NTP IP: time.chttl.com.tw
Secondary NTP : stdtime.gov.hk
<!--more--> =========================================================
LAN status: IP address : 192.168.1.1
MAC address : 00:D0:DA:00:18:51
Mask : 255.255.255.0
Dhcp status : Enable
Dhcp IP Start : 192.168.1.12 - 192.168.1.20
DNS IP address: 203.130.193.74
=========================================================
DHCP
reserved IP: MAC address IP address
-----------------------------------
=========================================================
Friday, December 24, 2010
MikroTik Wireless Configuration
Setup uses Safe Mode. It means that all changes that are made during setup
are reverted in case of error, or if Ctrl-C is used to abort setup. To keep
changes exit setup using the ‘x’ key.
Choose options by pressing one of the letters in the left column, before
dash. Pressing ‘x’ will exit current menu, pressing Enter key will select the
entry that is marked by an ‘*’. You can abort setup at any time by pressing
Ctrl-C.
Entries marked by ‘+’ are already configured.
Entries marked by ‘-’ cannot be used yet.
Entries marked by ‘X’ cannot be used without installing additional packages.
r - reset all router configuration
+ l - load interface driver
+ a - configure ip address and gateway
d - setup dhcp client
+ s - setup dhcp server
p - setup pppoe client
t - setup pptp client
* x - exit menu
your choice:
OR
[admin@MikroTik] > ip address
[admin@MikroTik] ip address> add address=192.168.1.1/24 interface=ether1
[admin@MikroTik] ip address> pr
# ADDRESS NETWORK BROADCAST INTERFACE
0 192.168.1.1/24 192.168.1.0 192.168.1.255 ether1
admin@MikroTik] ip address> /
[admin@MikroTik] >
[admin@MikroTik] >interface
[admin@MikroTik] interface> pr
Flags: X - disabled, D - dynamic, R - running
# NAME TYPE RX-RATE TX-RATE MTU
0 X ether1 ether 0 0 1500
1 X wlan1 wlan 0 0 1500
[admin@MikroTik] interface> enable 0
[admin@MikroTik] interface> enable 1
[admin@MikroTik] interface> pr
Flags: X - disabled, D - dynamic, R - running
# NAME TYPE RX-RATE TX-RATE MTU
0 R ether1 ether 0 0 1500
1 X wlan1 wlan 0 0 1500
[admin@MikroTik] ip address>add address=172.1.2.1/30 interface=wlan1
[admin@MikroTik] interface eoip>
[admin@MikroTik] interface eoip>add name=eoip-tunnel1 remote-address=172.1.2.2 tunnel-id=1 disabled=no arp=enabled
[admin@MikroTik] interface eoip>pr
Flags: X - disabled, R - running
0 R name=”eoip-tunnel1? mtu=1500 mac-address=FE:FD:00:00:00:00 arp=enabled remote-address=172.1.2.2 tunnel-id=1
[admin@MikroTik] interface eoip>..
[admin@MikroTik] interface>
[admin@MikroTik] interface> bridge
[admin@MikroTik] interface bridge> add name=bridge1
[admin@MikroTik] interface bridge>pr
Flags: X - disabled, R - running
0 R name=”bridge1? mtu=1500 arp=enabled mac-address=00:00:00:00:00:0 forward-protocols=ip,arp,appletalk,ipx,ipv6,other stp=no priority=32768 ageing-time=5m forward-delay=15s garbage-collection-interval=4s hello-time=2s max-message-age=20s
[admin@MikroTik] interface bridge>port
[admin@MikroTik] interface bridge port>pr
# INTERFACE BRIDGE PRIORITY PATH-COST
0 ether1 none 128 10
1 eoip-tunnel1 none 128 10
2 wlan1 none 128 10
[admin@MikroTik] interface bridge port>set eoip-tunnel1 bridge=bridge1
[admin@MikroTik] interface bridge port>set ether1 bridge=bridge1
[admin@MikroTik] interface bridge port>pr
# INTERFACE BRIDGE PRIORITY PATH-COST
0 ether1 bridge1 128 10
1 eoip-tunnel1 bridge1 128 10
3 wlan1 none 128 10
[admin@MikroTik] interface bridge port>.. ..
[admin@MikroTik] interface>wireless
[admin@MikroTik] interface wireless>set wlan1 mode=bridge disable-running-check=no band=5ghz frequency=5180 ssid=test1
Configurration For Mikrotik Station / Client
[admin@MikroTik] interface eoip>add name=eoip-tunnel1 remote-address=172.1.2.1 tunnel-id=1 disabled=no arp=enabled
[admin@MikroTik] interface wireless>set wlan1 mode=station disable-running-check=no band=5ghz frequency=5180 ssid=test1
[admin@MikroTik] interface>pr
Flags: X - disabled, D - dynamic, R - running
# NAME TYPE RX-RATE TX-RATE MTU
0 R ether1 ether 0 0 1500
1 R bridge1 bridge 0 0 1500
2 R eoip-tunnel1 eoip-tunnel 0 0 1500
3 R wlan1 wlan 0 0 1500
Belajar Msan
Login kedalam MSAN
>>User name:root
>>User password:
Huawei HONET UA5000 Universal Access Unit.
Copyright(C) 1998-2008 by Huawei Technologies Co., Ltd.
Command MSAN
MSAN01-D1-PPJ-1-MRF>enable
MSAN01-D1-PPJ-1-MRF#?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
active Enable configuration
alarm alarm command group
autosave autosave command group
backup backup command group
backup-server Backup information
baudrate Set serial baudrate
clear Clear alarm statistics table
client Users information
config Configuration from terminal
debugging debugging command group
diagnose Change into diagnose mode
disable Turn off privileged mode commands
display Display information
duplicate duplicate command group
equipment-mode Set the system MSAN working mode
erase Erase command
event Set event level
ftp FTP user and password configuration
igmp Internet Group Management Protocol keyword
infolevel Set the output level of the information terminal
infoswitch Set output switch of information terminal
load load command group
log Modify log configuration
loghost Log server configuration operation
monitor Change into monitor mode
patch Patch operation
quit Exit from current mode and enter prior mode
reboot Reboot system,active board or standby board
reset reset command group
resource System resources(mem,message,cpu)
rollback Active/standby mainboard rollback command
save The command of saving immediately
search Search command
serial-mode Set access-mode: console/CQT/112/SPL
set Set the operative time of rollback function
ssh Specify SSH (secure shell) configuration information
syslog Config the syslog information
sysname Set system network name
system system command group
terminal terminal command group
time time command group
timezone Set time zone
undo Negate a command or set its defaults
bandwidth Modify bandwidth or convergence
cls Clear screen
display Display information
help Description of the interactive help system
history-command Enable and control the command history function
idle-timeout Display interval of terminal timeout
interactive Enable or disable command execute confirm function
ping Check network connectivity or whether the host is
reachable
quit Exit from current mode and enter prior mode
scroll Set auto or manual scroll function
shutdown Deactivate the port on the standby board
smart Enable or disable smart function
switch Switch language mode
telnet Open a telnet connection
terminal Operation of config terminal
tracert Trace route to destination
undo Negate a command or set its defaults
Command MSAN
1. MSAN01-D1-PPJ-1-MRF#display version
{ |frameid/slotid<1,15> }:
Command:
display version
UA5000IPMBV100R017 RELEASE SOFTWARE
Copyright (C) 1998-2008 by Huawei Technologies Co., Ltd.
Uptime is 0 day(s), 8 hour(s), 11 minute(s), 9 second(s)
2. MSAN01-D1-PPJ-1-MRF#display system sys-info
--------------------------------------------------
The main service identification of this node:
78
The IP address of this node:
0.0.0.0
The physical location of this node:
Shenzhen China
The contact person for this managed node:
R&D Shenzhen, Huawei Technologies Co., Ltd.
The description of this node:
Huawei Integrated Access Software
--------------------------------------------------
3.MSAN01-D1-PPJ-1-MRF#display board 0/6
-------------------------------------
Board Name : H603ADRB
Board Status : Normal
Online state : -
-------------------------------------
RAT board is Normal
-----------------------------------------------------------------------------
Port Port Type Port Status Line Profile Alarm Profile Ext Profile
-----------------------------------------------------------------------------
0 ADSL Activated 17 1 --
1 ADSL Activating 17 1 --
2 ADSL Activating 17 1 --
3 ADSL Activating 17 1 --
4 ADSL Activating 17 1 --
5 ADSL Activating 17 1 --
6 ADSL Activating 17 1 --
7 ADSL Activating 17 1 --
8 ADSL Activating 17 1 --
9 ADSL Activating 17 1 --
10 ADSL Activating 17 1 --
11 ADSL Activating 17 1 --
12 ADSL Activating 17 1 --
13 ADSL Activating 17 1 --
14 ADSL Activating 17 1 --
15 ADSL Activating 17 1 --
16 ADSL Activating 17 1 --
17 ADSL Activating 17 1 --
18 ADSL Activating 17 1 --
19 ADSL Activating 17 1 --
20 ADSL Activating 17 1 --
21 ADSL Activating 17 1 --
22 ADSL Activating 17 1 --
23 ADSL Activating 17 1 --
24 ADSL Activating 17 1 --
25 ADSL Activating 17 1 --
26 ADSL Activating 17 1 --
27 ADSL Activating 17 1 --
28 ADSL Activating 17 1 --
29 ADSL Activating 17 1 --
30 ADSL Activating 17 1 --
31 ADSL Activating 17 1 --
-----------------------------------------------------------------------------
Total number of activated port : 1
Total number of unactivated port: 31
port 1 sedang up
>>User name:root
>>User password:
Huawei HONET UA5000 Universal Access Unit.
Copyright(C) 1998-2008 by Huawei Technologies Co., Ltd.
Command MSAN
MSAN01-D1-PPJ-1-MRF>enable
MSAN01-D1-PPJ-1-MRF#?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
active Enable configuration
alarm alarm command group
autosave autosave command group
backup backup command group
backup-server Backup information
baudrate Set serial baudrate
clear Clear alarm statistics table
client Users information
config Configuration from terminal
debugging debugging command group
diagnose Change into diagnose mode
disable Turn off privileged mode commands
display Display information
duplicate duplicate command group
equipment-mode Set the system MSAN working mode
erase Erase command
event Set event level
ftp FTP user and password configuration
igmp Internet Group Management Protocol keyword
infolevel Set the output level of the information terminal
infoswitch Set output switch of information terminal
load load command group
log Modify log configuration
loghost Log server configuration operation
monitor Change into monitor mode
patch Patch operation
quit Exit from current mode and enter prior mode
reboot Reboot system,active board or standby board
reset reset command group
resource System resources(mem,message,cpu)
rollback Active/standby mainboard rollback command
save The command of saving immediately
search Search command
serial-mode Set access-mode: console/CQT/112/SPL
set Set the operative time of rollback function
ssh Specify SSH (secure shell) configuration information
syslog Config the syslog information
sysname Set system network name
system system command group
terminal terminal command group
time time command group
timezone Set time zone
undo Negate a command or set its defaults
bandwidth Modify bandwidth or convergence
cls Clear screen
display Display information
help Description of the interactive help system
history-command Enable and control the command history function
idle-timeout Display interval of terminal timeout
interactive Enable or disable command execute confirm function
ping Check network connectivity or whether the host is
reachable
quit Exit from current mode and enter prior mode
scroll Set auto or manual scroll function
shutdown Deactivate the port on the standby board
smart Enable or disable smart function
switch Switch language mode
telnet Open a telnet connection
terminal Operation of config terminal
tracert Trace route to destination
undo Negate a command or set its defaults
Command MSAN
1. MSAN01-D1-PPJ-1-MRF#display version
{ |frameid/slotid<1,15> }:
Command:
display version
UA5000IPMBV100R017 RELEASE SOFTWARE
Copyright (C) 1998-2008 by Huawei Technologies Co., Ltd.
Uptime is 0 day(s), 8 hour(s), 11 minute(s), 9 second(s)
2. MSAN01-D1-PPJ-1-MRF#display system sys-info
--------------------------------------------------
The main service identification of this node:
78
The IP address of this node:
0.0.0.0
The physical location of this node:
Shenzhen China
The contact person for this managed node:
R&D Shenzhen, Huawei Technologies Co., Ltd.
The description of this node:
Huawei Integrated Access Software
--------------------------------------------------
3.MSAN01-D1-PPJ-1-MRF#display board 0/6
-------------------------------------
Board Name : H603ADRB
Board Status : Normal
Online state : -
-------------------------------------
RAT board is Normal
-----------------------------------------------------------------------------
Port Port Type Port Status Line Profile Alarm Profile Ext Profile
-----------------------------------------------------------------------------
0 ADSL Activated 17 1 --
1 ADSL Activating 17 1 --
2 ADSL Activating 17 1 --
3 ADSL Activating 17 1 --
4 ADSL Activating 17 1 --
5 ADSL Activating 17 1 --
6 ADSL Activating 17 1 --
7 ADSL Activating 17 1 --
8 ADSL Activating 17 1 --
9 ADSL Activating 17 1 --
10 ADSL Activating 17 1 --
11 ADSL Activating 17 1 --
12 ADSL Activating 17 1 --
13 ADSL Activating 17 1 --
14 ADSL Activating 17 1 --
15 ADSL Activating 17 1 --
16 ADSL Activating 17 1 --
17 ADSL Activating 17 1 --
18 ADSL Activating 17 1 --
19 ADSL Activating 17 1 --
20 ADSL Activating 17 1 --
21 ADSL Activating 17 1 --
22 ADSL Activating 17 1 --
23 ADSL Activating 17 1 --
24 ADSL Activating 17 1 --
25 ADSL Activating 17 1 --
26 ADSL Activating 17 1 --
27 ADSL Activating 17 1 --
28 ADSL Activating 17 1 --
29 ADSL Activating 17 1 --
30 ADSL Activating 17 1 --
31 ADSL Activating 17 1 --
-----------------------------------------------------------------------------
Total number of activated port : 1
Total number of unactivated port: 31
port 1 sedang up
Subscribe to:
Posts (Atom)